- 您现在的位置：买卖IC网 > Sheet目录342 > MCZ33927EK (Freescale Semiconductor)IC FET PRE-DRIVER 3PH 54-SOIC
FUNCTIONAL DESCRIPTIONS
INTRODUCTION
reference for the SPI port. A 0.47μF (min) decoupling
capacitor must be connected to this pin.
This regulator is intended for internal IC use and can
supply only a small (1mA) external load current.
A power-on-reset (POR) circuit monitors this pin and until
the voltage rises above the threshold, the internal logic will be
reset; driver outputs will be tri-stated and SPI communication
disabled.
The VDD regulator can be disabled by asserting the RST
signal low. The VDD regulator is powered from the VPWR
pin.
PHASE B HIGH-SIDE CONTROL INPUT (PB_HS)
This pin is the input logic signal, enabling the High-Side
driver for Phase B. The signal is active low, and is pulled up
by an internal current source.
PHASE B LOW-SIDE INPUT (PB_LS)
This pin is the input logic signal, enabling the Low-Side
driver for Phase B. The signal is active high, and is pulled
down by an internal current sink.
INTERRUPT (INT)
The Interrupt pin is a totem pole logic output. When a fault
is detected, this pin will pull high until it is cleared by
executing the Clear Interrupt command via the SPI port. The
faults capable of causing an interrupt can be masked via the
MASK0 and MASK1 SPI registers to customize the
response.
PHASE C LOW-SIDE INPUT (PC_LS)
This input logic pin enables the Low-Side Driver for Phase
C. This pin is an active high, and is pulled down by an internal
current sink.
PHASE C HIGH-SIDE INPUT (PC_HS)
This input logic pin enables the High-Side Driver for Phase
C. This signal is active low, and is pulled up by an internal
current source.
AMPLIFIER OUTPUT (AMP_OUT)
This pin is the output for the current sensing amplifier. It is
also the sense input to the overcurrent comparator.
AMPLIFIER INVERTING INPUT (AMP_N)
The inverting input to the current sensing amplifier.
AMPLIFIER NON-INVERTING INPUT (AMP_P)
The non-inverting input to the current sensing amplifier.
OVERCURRENT COMPARATOR OUTPUT
(OC_OUT)
The overcurrent comparator output is a totem pole logic
level output. A logic high indicates an overcurrent condition.
OVERCURRENT COMPARATOR THRESHOLD
(OC_TH)
This input sets the threshold level of the overcurrent
comparator.
CHIP SELECT (CS)
Chip select is a logic input that frames the SPI commands
and enables the SPI port. This signal is active low, and is
pulled up by an internal current source.
SERIAL IN (SI)
The Serial In pin is used to input data to the SPI port.
Clocked on the falling edge of SCLK, it is the most significant
bit (MSB) first. This pin is pulled down by an internal current
VOLTAGE SOURCE SUPPLY (VSS)
VSS is the ground reference for the logic interface and
power supplies.
GROUND (GND0,GND1)
These two pins are connected internally to VSS by a 1.0 ?
resistor. They provide device substrate connections and also
the primary return path for ESD protection.
sink.
VLS REGULATOR CAPACITOR (VLS_CAP)
SERIAL CLOCK (SCLK)
This logic input is the clock is used for the SPI port. The
SCLK typically runs at 3 MHz (up to 5 MHz) and is pulled
down by an internal current sink.
SERIAL OUT (SO)
Output data for the SPI port streams from this pin. It is tri-
stated until CS is low. New data appears on rising edges of
SCLK in preparation for latching by the falling edge of SCLK
on the master.
This connection is for a capacitor which will provide a low
impedance for switching currents on the gate drive. A low
ESR decoupling capacitor, capable of sourcing the pulsed
drive currents must be connected between this pin and VSS.
This is the same DC node as VLS, but it is physically
placed on the opposite end of the IC to minimize the source
impedance to the gate drive circuits.
PHASE C GROUND (PGNDC)
The phase C power ground is the pin used to return the
gate currents from the low side FET. Best performance is
normally realized by connecting this node directly to the
source of the low side FET for phase C.
33927
Analog Integrated Circuit Device Data
Freescale Semiconductor
21
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MCZ33937EKR2
IC PRE-DRIVER 3PHASE 54-SOIC
MDN2BL3GRAS
MOTOR BRUSHED DC 2V 2753RPM
MDN3BL3CSAS
MOTOR BRUSHED DC 2V 1458RPM
MIC2287-34YML TR
IC LED DRIVER WHITE BCKLGT 8-MLF
MIC2289C-34YD6 TR
IC LED DRIVR WHITE BCKLGT TSOT-6
MIC2291YD5 TR
IC LED DRIVER PHOTO FLASH TSOT-5
MIC2293-15YML TR
IC LED DRIVER WHITE BCKLGT 8-MLF
MIC2293C-34YML TR
IC LED DRIVER WHITE BCKLGT 8-MLF
相关代理商/技术参数
MCZ33927EK/R2
制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Three-Phase Field Effect Transistor Pre-Driver
MCZ33927EKR2
功能描述:功率驱动器IC THREE PHASE PRE- DRIVER RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MCZ33927R2
制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Three-Phase Field Effect Transistor Pre-Driver
MCZ33937AEK
功能描述:马达/运动/点火控制器和驱动器 3 Phase Pre-Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MCZ33937AEK/R2
制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Three Phase Field Effect Transistor Pre-driver
MCZ33937AEKR2
功能描述:马达/运动/点火控制器和驱动器 3 Phase Pre-Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube
MCZ33937EK
功能描述:功率驱动器IC THREE PHASE PRE DRIVER RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MCZ33937EK/R2
制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Three Phase Field Effect Transistor Pre-driver